esSJae's Virtualization Blog

Virtualization and other IT topics

Archive for May 14th, 2015

Windows 10 Hyper-V: Setting up Networking Shared and Bridged Options

Posted by essjae on May 14, 2015

Update:  It’s now a lot easier to create networks (using PowerShell) in Windows 10 Hyper-V:  https://smudj.wordpress.com/2016/03/10/adding-nat-to-hyper-v-in-windows-10-and-higher/

Update 2:  Windows 10 now creates the Default Switch automatically, which is a non-configurable NAT virtual switch for Hyper-V.

Update 3: If you need a configurable NAT router, see step 2 shown here: https://smudj.wordpress.com/2019/03/18/the-poor-techs-hyper-v-lab-setup/ 

 

 

 

******Deprecated****** 

I do not recommend this method any longer.  Use one options from the updates above

Update: Build 10586.3–Loopback adapter was missing, added back, and checked Hyper-V Extensible Virtual Switch.  This seems to happen with each build update.  A reboot may also be required.

This procedure shows you how to set up bridged and shared (NAT) networking with a single physical network card.

Standard Bridged Networking

  1. Start the Hyper-V Manager and click Virtual Switch Manager
  2. Select External and click Create Virtual Switch
  3. Enter Bridged or similar to identify this network as being on your physical network
  4. Select the correct network adapter under External network, this should be an active network card, i.e. one that is connected to your network and your host is using.
    1. If you only have one network card, verify that Allow management operating system to share this network adapter.
    2. If you have multiple network cards, and want to use this card exclusively for VMs, uncheck Allow management operating system to share this network adapter.
  5. Click OK and the new virtual switch will be created.
  6. Verify that you don’t have any ongoing network tasks before clicking yes, as your network connection will likely be disrupted when the virtual switch is created.
  7. This will create a network adapter under Network Connections called vEthernet (name_used), in this case, vEthernet (Bridged)

Shared Networking

Manually add a loopback adapter

  1. Open a cmd prompt with Administrator privileges.
    1. Type cmd, right-click on the search result and click Run as administrator
  2. Type hdwwiz and press enter
  3. add-new-hardware-wizard
  4. Click Next to start the wizard.
  5. Select Install the hardware that I manually select from a list (Advanced), and click
  6. Highlight Network Adapters, and click Next.
  7. Select Microsoft from the Manufacturer column and Microsoft KM-TEST Loopback Adapter from the Model column and click Next.
  8. ms-loopback
    1. Click Finish to complete the wizard.
    2. Open Network Connections (CTRL+X and select Network Connections), locate the newly created loopback adapter, right-click it and click Rename, and rename it from Ethernet 2 or Ethernet 3 to Loopback.

Create the Shared Virtual Network Switch in Hyper-V

  1. Open the Hyper-V Manager and click Virtual Switch Manager
  2. Select External and click Create Virtual Switch
  3. Enter a descriptive name, like Shared or NAT. This will create a network adapter under Network Connections called vEthernet (name_used), in this case, vEthernet (Shared)
  4. Select the Loopback adapter under the External Network selection box, click OK, then click Yes, this operation will not disrupt your host networking.

Connect the Loopback Adapter and Virtual Switch to the Network

  1. Open Network Connections (CTRL+X and select Network Connections)
  2. Click Change adapter settings
  3. Right-click and select Properties on the vEthernet (Bridged) network adapter created under Standard Bridged Networking.
  4. Click the Sharing
  5. Click Allow other network users to connect through this computer’s Internet connection.
  6. vEthernet(bridged)
  7. Select the Shared network connection, it should be listed as vEthernet (Shared), or whatever name was used in place of Bridged.
  8. Click Ok.

Note:  The Hyper-V networking is very fragile here, and you may need to reboot if you get errors when trying to connect and share the connections.

Here’s the completed Network Connections Window, note the Bridged and Shared Hyper-V adapters. Apologies for the pixelation, the Hyper-V Manager is not 4K screen friendly.

virtual_switches

Here’s two VMs using the Shared networking, note, the 192.168.137.x network, the default used by ICS.  Also shown is a third VM using the host network and the host’s IP.

IPconfigs-4

Posted in Computers, Hyper-V, Windows 10 | Tagged: , , , , | 7 Comments »